GPS Car Alarm G110Q SMS COMMAND

GPS Car Alarm G110Q SMS COMMAND

Functions & Features

 (1)Check the car’s location, speed & direction via SMS;

(2)Cut off the car power/fuel supply by SMS, to stop the car;

(3)Movement Alert:

Once the car is parked, you can send the SMS instruction to put the system in movement alert status. Then, if the car moves, the system will send SMS to inform you. It is a very useful function, which enables the tracker to work as the car alarm too;

(4) Geo-fence Alert:

User can set a certain zone by SMS, once the vehicle runs over the fence, the alarm will send SMS to inform you;

(5) Over-speed Alert.

User can set a certain speed limitation by SMS. Once the vehicle is running over this speed, the system will send SMS to inform you;

(6) Built-in rechargeable backup battery. If the system’s main power supply is cut off or low enough, system will send SMS to warn you;

(7) Two kinds of location information; user could locate the precise location by GPS. If there is no GPS signal, user could also locate the car by CPS (cellular positioning system - located by GSM network)

(8) Monitor the voice around the car via telephone;

(9) Anti-robbery switch, send out SMS for help in case of hijack; (optional function)

(10) Track the car by SMS or by online mapping (The software is optional).

(11) Flexible design, the system can work alone without support of center. If the center is set up, the functions can be much stronger, you can monitor & control many vehicles in the center, and the information of vehicle’s location can be more detailed and friendly.

(12) Anti-tamper design in small size, stable, reliable & easy installation.

(13) Support SMS & GPRS communication

(14) The Alert Text in SMS can be re-defined in different languages.

Explanation on SMS Message

       When the alarm is triggered, it will send the alert SMS message to the authorized mobile. This SMS alarm message includes:

²       Alarm type. “Be robbed”, “Power failure”, etc..

²       Base station’s code of GSM signal relay tower. The GSM operator can tell you the location by this code because they have the related database. In some countries, this function is not open to the public.

²       Latitude & longitude. User could locate the car’s precise position by help of GOOGLE MAP (http://maps.google.com/) or GOOGLE EARTH (Download link: http://earth.google.com/).

²       GPS signal’s Status: A : GPS’s signal is available, the car is at broad outside place; V: GPS’s signal is shielded, the car is at the underground; H: The car pass through 10 GSM base stations, but the received GPS’s data doesn’t change, it means that there is no GPS signal or GPS’s receiver is damaged

²       Speed. The car’s speed in KM/H.

²       Direction: The car’s direction is showed in this message. (In coordinates, start from line of the north direction, turn over an angle in the certain degree clockwise.)

     Example: The above message shows that: the SOS anti-robbery button is pressed down. The GSM base station code of the car is 25023722, the car is at outdoors & GPS signal is available, the latitude is 23.1430N, the longitude is 113.3390E, the car’s speed is 0KM/H, and the car’s direction is north.     

How to Operate It

  Arm/Disarm by Phone Calling

 User could also use the first alarm-received mobile phone to call the system SIM card number, so as to arm/disarm the system.

Arm: After hearing several ring tones, if the systems hang up the call automatically, and call back you, it means that the system is armed.

Disarm: After hearing several ring tones, if the system hangs up the call automatically, and don’t call back you, it means that the system is disarmed.

Note:

(1)   There is no communication fee for this operation, it is a very convenient way to arm & disarm the system.

(2)The SIM card inside the device must have the function of Caller ID Display.

(3) Only the 1st authorized mobile phone can realize this function.

 SMS Control Instructions

User can send SMS instruction to operate the tracker by any mobile phone, the format of the instruction is:

User Password(******)+ Control Code(XXX)

The default user password is 111111.

If the user password is changed, user should send the SMS instruction with the new user password instead of 111111.

XXX is the control code, all the letters must be capital letters or small letters.

There is no space between the user password & the control instruction.

Authorize the Alert-received Mobile

In case of alarm, if user wants to get the alert SMS from the tracker, he/she needs send the following SMS to program the system firstly:

 111111*10 Mobile #1*20 Mobile #2*

 Other functions:

Mobile #1: it is used to call the tracker No., system will be armed /disarmed

Mobile #2: it is used to call the tracker No., system will send back location SMS to the mobile #2

Example: User sends the SMS 111111*1013922713571*2013711189059* to the tracker’s SIM card number, if there is any alert, system will send alert SMS to both of these two mobiles. If user uses mobile 13922713571 to call tracker No., system will be arm/disarm; if user uses mobile 13711189059 to call the tracker No., system will send back location SMS to the mobile 13711189059.

l        111111PSWnnnnnn

This instruction is used to change the user password. The length of the user’s password is 3~6 digits. Users are suggested to change to the new password in use.

Example: User sends the SMS “111111PSW12345” to the system SIM card number, and gets the confirmed SMS “111111PSW12345” in 3 seconds. It means that the user password has been changed to 12345.

Remark: Please keep the password deep in mind if it is changed.

l        111111ARM

This instruction is used to arm the system.

The system will send back the confirmed SMS to you, such as “Unit Armed! ……”

l        111111DSM

This instruction is used to disarm the system, to stop receiving the alert SMS from the tracker.

The system will send back the confirmed SMS to you, such as “Unit Disarmed! ……”

l        111111CHK

This instruction is used to inquiry the vehicle’s location & system’s status.

The system will send back the SMS, includes the similar information, such as “Unit Disarmed……”

l        111111STP

This instruction is used to cut off the car’s power supply or fuel supply, so as to stop the car.

      The car will be controlled to stop gradually.

Attention: It is very dangerous to stop the car when the vehicle is running at high speed. We do not take any responsibility to the consequence caused by this action.

l        111111STPN  or 111111STP(N)

This instruction is used to stop the car under the condition of speed limitation.

If the car is running at speed higher than N (KM/H), the instruction will not be carried out. System will send back feedback SMS “No parking, vehicle …”; If the car’s speed is less than the value N , it will be controlled to stopped gradually.

Example: N =40. The car is running at speed of 50KM/H, user send 111111STP40 or 111111STP(40) to system, the system will send back SMS “No parking.” to warn user that the condition is not met. Once the car’s speed is about 39KM/H, the system will automatically carry out this instruction & stop the car.

The Minimum value of N is 30KM/H

l        111111RES

This instruction is used to restore the car to normal status after stopping the car.

It is also used to stop the receiving of SOS alert SMS once the anti-robbery SOS switch is pressed down.

l        111111MONP

This instruction is used to monitor the voice around the car. The SIM card inside the system pays for the communication fee.

The P is the telephone which is used to monitor the voice. When user send out this SMS to the system, the system will call back the telephone P, user could listen in the voice around the car upon picking up the call.

If you use the present mobile to carry out the monitoring, you can let the P as blank, sending 111111MON is OK.

Example: P =13780012345. If user sends 111111MON13780012345 to system, the system will call back the phone 13780012345 immediately. Once upon pickup the call from the system, user can hear the voice around.

l        111111MON:Phone No.

This instruction is used to monitor the voice around the car. The user’s telephone pays for the communication fee.

Example: User uses the telephone 38351400 to carry out monitoring and pay the communication fee, user can send 111111MON:38351400 to the tracker firstly, then use this phone 38351400 to call the tracker, it will be connected automatically to monitor the voice. This setting is stored all the time until you change it to another phone no.

Remark: please do not set the user’s 1st alert-received phone no. as this phone no.

SOS Anti-robbery Alert

It is the optional function, it needs the optional component: SOS switch.

If you program the 1st & 2nd alert-received mobile only, once the SOS switch is pressed down & hold for at least 3 seconds, the system will send alarm SMS to the  1st & 2nd alert-received mobile. User can send command 111111RES to release it.

If you program the 3rd alert-received mobile as the center number, once the SOS switch is pressed down & hold for at least 3 seconds, the system will ONLY send alarm SMS to the center number. (the 3rd mobile no.). User can send command 111111RES to release it.

Movement Alert

  111111MOV0  to disable the movement alert

 111111MOV1  to enable the movement alert, the present location is the center.

111111MOV？ to check the center’s position.

  Once the system is armed, the movement alert will be automatically enabled. Once the system is disarmed, the movement alert will be automatically disabled.

111111RAD:XR:a,YR:b  to define the distance for triggering the alert

 Example: If you want to set the radius in latitude as 60meters, radius in longitude as 80 meters, you can send 111111RAD:XR:60,YR:80 to the tracker. This setting will be stored in the tracker all the time until you change it again.

Geo-Fence Alert

 Format of SMS instructions:

111111FEN0   Disable the Geo-fence

111111FEN1   Enable the Geo-fence, using the stored setting

111111FEN1()  Enable the geo-fence, using the latitude & longitude of present location, the distance of latitude & longitude are 1000 meters.

111111FEN？  Check the setting of geo-fence

111111RAL:XR:a,YR:b,X:c,Y:d

Or 111111RAL:XR:a,YR:b

Or 111111RAL:X:c,Y:d

 XR:a,  a is the distance of latitude (Meter)

 YR:b,  b is the distance of longitude (Meter)

X:c,    c is latitude(degree), the range of the value is 0-90）

 Y:d,    d longitude (degree), the range of the value is 0~180）

Remark: (1) RAL, XR, YR, X, Y must be in capital letter.

        (2) The Setting will be stored.

 Example: If the fence is a circle with Radius of 5000meters, the coordinates of the circle’s center is: latitude:+23.1400, longitude:+113.4500, then the SMS instruction is:  111111RAL:XR:5000,Y:5000,X:23.1400,Y:113.4500 . If the vehicle is running across the boundary of the fence, the system will automatically send out Alert SMS.