SMS command of GPS tracker TK111

SMS command of GPS tracker TK111

111111PSWnnnnnn

This instruction is used to change the user password. The length of the user’s password is 3~6 digits. Users are suggested to change to the new password in use.

 Example: User sends the SMS “111111PSW12345” to the system SIM card number, and gets the confirmed SMS “111111PSW12345” in 3 seconds. It means that the user password has been changed to 12345.

111111ARM

This instruction is used to arm the system.

The system will send back the confirmed SMS to you, such as “System Armed! Vehicle position: ……”

111111DSM

This instruction is used to disarm the system.

The system will send back the confirmed SMS to you, such as “System Disarmed! Vehicle position: ……”

111111CHK

This instruction is used to inquiry the vehicle’s location & system’s status.

The system will send back the SMS, includes the similar information, such as “System Disarmed, Engine off! Door Opened! Vehicle position: ……”

111111MAP

This instruction is used to the location with Google Map Link.

 Upon receiving the SMS command, the tracker will automatically send back the SMS including the Google map’s URL, user can use smart phone (GPRS data service is enabled) to open the URL link, the car’s location will be showed on the Google map.

111111STP

This instruction is used to cut off the car’s power supply or fuel supply, so as to stop the car. The car will be controlled to stop gradually.

 Attention: It is very dangerous to stop the car when the vehicle is running at high speed. We do not take any responsibility to the consequence caused by this action.

 111111STPN

This instruction is used to stop the car under the condition of speed limitation. If the car is running at speed higher than N (KM/H), the instruction will not be carried out. System will send back feedback SMS “No parking, vehicle …” If the car’s speed is less than the value N, it will be controlled to be stopped gradually.

After you send 111111STPN to the system already, from then on, if you send 111111STP, it will carry out this operation (111111STPN) always.

You can send 111111STP0 to disable this function, from then on, if you send 111111STP, the car will stop immediately.

 Example: N =30. The car is running at speed of 50KM/H, user send 111111STP30 to system. The system will send back SMS “No parking.” to warn user that the condition is not met. Once the car’s speed is about 29KM/H, the system will automatically carry out this instruction & stop the car.

111111RES

This instruction is used to restore the car to normal status after stopping the car.

111111MONP

This instruction is used to monitor the voice around the car. The SIM card inside the system pays for the communication fee. The P is the telephone which is used to monitor the voice. When user send out this SMS to the system, the system will call back the telephone P, user could listen in the voice around the car upon picking up the call. If user wants the tracker call back the present phone, the P can be empty, such as 111111MON that is OK.

 Example: P =13780012345. If user sends 111111MON13780012345 to system, the system will call back the phone 13780012345 immediately. Once upon pickup the call from the system, user can hear the voice around.

 111111MON！

This instruction is used to monitor the voice around the car. The user’s telephone pays for the communication fee.

 Example: User uses the mobile 13780012345 to send 111111MON! to the system. The system will send back the message: “Ok, please call me in 2 minutes!” If user calls the system via the mobile 13780012345 inside 2 minutes, the system will be automatically connected, and user can monitor the voice around.

Movement Alert

 111111MOV0 to disable the movement alert

 111111MOV1 to enable the movement alert, the present location is the center.

 111111MOV？ To check the center’s position.

  Once the system is armed, the movement alert will be automatically enabled. Once the system is disarmed, the movement alert will be automatically disabled.

Usage: This function enables the tracker to work as a GSM car alarm.

Example: After the car is parked, you can use the 1st authorized mobile phone to call the system. The system will be armed & the Movement Alert function is enabled automatically. Then, once the car is moved about 30 meters away from the parking location, the system will immediately send SMS to warn you.

Geo-Fence

Instruction: 111111FENx(XL:a,YL:b,X:c,Y:d)

Or 111111FENxXL:a,YL:b,X:c,Y:d

 If x=0, disable the function of geo-fence;

 If x=1, enable the function of geo-fence;

 XL:a, a is latitude(degree), the range of the value is 0-90）

 YL:b, b longitude (degree), the range of the value is 0~180）

 X:c,  c is the distance of latitude (Meter)

 Y:d,  d is the distance of longitude (Meter)

Format of SMS instructions:

111111FEN？   Check the setting of geo-fence

111111FEN0    Disable the Geo-fence

111111FEN1   Enable the geo-fence, using the parameters of the previous setting

111111FEN1()  Enable the geo-fence, using the latitude & longitude of present location, the distance of latitude & longitude are 1000 meters.

111111FEN1(X:c) only change the distance of latitude, the other parameters keep the same.

111111FEN1(Y:D)  only change the distance of longitude, the other parameters keep the same. The function of geo-fence does not have relation with Arming or Disarming.

Example: If the fence is a circle with Radius of 500meters, the coordinates of the circle’s center is: latitude:+23.1400, longitude:+113.4500, then the SMS instruction is:  111111FEN1(XL:23.1400,YL: 113.4500,X:500,Y:500). If the vehicle is running across the boundary of the fence, the system will automatically send SMS to warn you.

Over-speed Alert

111111SPD:X    x is the speed in KM/H , maximum value is 250KM/H 

 (For example: 111111SPD:60, if the car speed is over 60KM/H, it will send SMS to warn you)

111111SPD:?   to check the setting of over-speed alert.

How to disable this function: You can send 111111SPD:250 to disable this Over-speed Alert

Change the Time Zone

111111ZON:T    T is the time zone in minutes.

Example:  111111ZON:480      : time zone is 8

              111111ZON:-60      : time zone is -1

Automatic Report by SMS

111111RPT:NNN:T  

NNN represents the 1-3 alarm-received phone no. (N=1 or 0, 1: enable, 0: disable)

T is the time interval in minutes. If T=0, to disable the auto-reporting

Example:  111111RPT:001:5

Tracker sends location by SMS to 3rd number for every 5 minutes;

111111RPT:101:10

Tracker sends location by SMS to 1st & 3rd number for every 10 minutes;

Change the Center Password

CEN666666*40new password*

This instruction is used to change the center’s password. There is no need for the user to change it if it is not connected to center.

Example:   CEN666666*40777777*

Specifications

Size of the main unit: 7.5*5.4*2.5 (CM)

Weight of the main unit: 0.1KG

Working temperature: -20 ~ 70℃

Humidity: 0 ~ 95%

GSM frequencies: Dual-band:900MHz/1800MHz

GPS chip: Latest SiRF-Star III chipset

Working voltage: 12 VDC

Power Consumption:  Working current: 20~1000mA; Static current: 20~30mA; Peak current of sending GSM signal: 1000~1200mA; Peak

current of receiving GSM signal: 600~800mA;

Inside Backup battery: Rechargeable 3.7V 800mAh Li-ion battery